Throughout this article, we’ll explain what “Battery Saver Mode” means, the main causes of it, and how to reset it.
Let’s get started!
Dodge Journey ‘Battery Saver Mode’ Mean?
In order for your Dodge Journey to operate properly, a healthy battery is essential.
You will be able to run the air conditioning, radio, and navigation systems on your Dodge Journey with the help of this battery.
As a result, the starter motor is also powered up when your engine is started.
Some of these systems will be turned off automatically by the computer if the battery voltage drops below a certain level.
In “Battery Saver Mode”, your car’s battery is protected from draining completely, so you won’t have to worry about it stalling.
A Battery Saver Mode alert may cause the following symptoms:
- There may be a problem starting your Dodge Journey.
- Lights may dim inside and outside.
- You may have a problem with your infotainment screen.
- Stalls may occur in the car.
- It is possible for Windows to malfunction.
- Alert for the Battery Saver Mode
“Battery Saver Mode” Alert on Dodge Journey
The battery saver mode has now been briefly explained. This fault message could have a few causes.
1. A dead battery:
Bad batteries cause Dodge Journeys to display “battery saver mode” messages.
In most cases, the problem is caused by an old, depleted battery.
Eventually, the battery loses power and becomes less capable of holding a charge.
As a result, your battery won’t get charged properly by your alternator;
In this way, the Dodge Journey prevents the battery from overcharging while you are driving by entering “battery saver mode.”.
During my career as a mechanic, I have found that Dodge Journey batteries need to be replaced every 3-5 years.
It may be time for you to replace your car battery if it’s older than this.
Using a jumper cable is the most effective way to diagnose a bad battery.
This suggests the battery is defective, so you should replace it if it fixes the problem.
2. Faulty Alternator:
Battery saver active problems can also be caused by damaged alternators.
Your car battery is charged by the alternator, which generates electricity.
Unless your alternator is working properly, you won’t be able to start your car or do anything electrical.
Dodge Journey’s battery might not be charged as a result, causing it to enter “battery saver mode”.
Instead, things are going the other way.
If the vehicle won’t start, you can check if there is a problem with the alternator.
After that, let it run for several minutes (3-5 minutes).
Once you have disconnected the negative terminal of the battery, reconnect it.
It’s a sign that the alternator is bad if it turns off when you disconnect the negative terminal.
It is not your alternator that is malfunctioning if your car runs despite disconnecting one terminal.
3. Batteries with loose terminals:
The loose battery terminals may also be responsible for the Dodge Journey’s “Battery saver mode” display.
The alternator cannot deliver power to the battery when battery terminals are loose.
As a result, your vehicle’s battery has difficulty charging and operating at its maximum capacity.
Your Dodge Journey may enter battery saver mode if you have a loose battery terminal.
4. Serpentine belt worn out:
It connects the pulley on your alternator to other components like your power steering pump and air conditioning. The serpentine belt is also known as the alternator belt.
Wear and tear can cause this belt to break, resulting in a malfunction of the pulleys, which affects the alternator.
It will display a warning message saying “Battery saver mode”.
How to Reset “Battery Saver Mode” Message on Dodge Journey
As a final note, let’s examine how this warning message can be combated.
Battery terminals should be checked
Make sure the battery terminals are tight as the first thing you should do.
You should tighten them with a screwdriver if they are loose.
Furthermore, you should check if the battery itself and its terminals don’t show any signs of corrosion.
Wire brushes and hot water can be used to remove corrosion.
When the message still appears, reconnect the battery terminals and proceed to step two.
2. Change the battery
A new battery is necessary if the terminals of the car’s battery are not corroded.
It is important that you have your battery tested before changing it (you can have this done at your dealer or at an auto store like Autozone).
You may have a dead battery because you didn’t drive long enough, or something else.
If your Dodge Journey battery is over three years old, you might not need to replace it.
In order to verify whether or not the message is still visible on your dashboard after changing your car battery, restart your car.
Battery replacement is usually the solution.
3. Test or replace the alternator
A faulty alternator may be the cause of a dead battery.
Make sure it’s working right and replace it if needed. While you are idling, a good alternator should display a voltage reading of between 13.5 and 14.5 volts.
NOTE: Other factors can also trigger this alert, including a damaged ground wire or a blown battery sensor fuse, but in my experience, these are the most common cause.
Related Articles
What Causes Spark Plug Electrode To Bend?
Toyota RAV4 Prime Tax Credit Eligibility [Explained]
Mini Cooper Drivetrain Malfunction 2024 [Explained]
What Happens If You Don’t Grease Brake Pads?
Frequently Asked Questions
What is Battery Saver Mode?
Battery Saver Mode is a feature in the Dodge Journey designed to prevent battery drain. It automatically turns off non-essential electrical components, such as lights and the radio, after a short period of inactivity (typically around 10 minutes) to conserve battery power when the engine is not running.
Why does Battery Saver Mode activate?
This mode activates when the vehicle’s battery voltage drops below a certain threshold, indicating that the battery may not be adequately charged. Common causes include a failing alternator, weak battery, or issues with the vehicle’s charging system.
How can I tell if my vehicle is in Battery Saver Mode?
When activated, a message will typically appear on the dashboard indicating “Battery Saver Mode.” You may also notice that certain electrical components, like the radio or interior lights, turn off automatically.
Can I reset Battery Saver Mode?
There isn’t a specific reset for Battery Saver Mode. However, resolving underlying issues such as replacing a faulty battery or alternator may stop the mode from activating again. If problems persist, consider consulting a mechanic for diagnostics.
Is it safe to drive with Battery Saver Mode activated?
While it may be possible to drive with Battery Saver Mode activated, it indicates that there is an issue with your vehicle’s electrical system that needs addressing. Continuing to drive under these conditions could lead to further problems, including getting stranded due to a dead battery.
